• bestpath costcommunity ignore

    Hi, This is my current scenario: AS2 –>  PE2 [MPLS] PE1  <– AS1 - AS1: advertises prefix 122.1.1.7 to MPLSv4 network via EIGRP redistribution to the PE1 - MPLSv4 Network advertises 1...
    Francesco
    last modified by Francesco
  • OSPF Stubs with virtual links part 3

      https://wp.scsiraidguru.com/?page_id=2109   I took part 2 and configured all four types of OSPF stubs. 
    Michael
    last modified by Michael
  • ISAKMP phase is not establishing when i add ASA between routers?

    i place ASA between two router and allow udp 500 in asa but isakmp phase is not negotiating. what can be the problem? i want to establish site to site vpn between routers. please tell me any solution. thanks.
    shantilal
    created by shantilal
  • Since I have ECMP in VxLAN, how do I avoid out of order packets arriving at the leaf? Especially when the inital payload was also UDP ?

    Since I have ECMP in VxLAN, how do I avoid out of order packets arriving at the leaf? Especially when the inital payload was also UDP ? ... there are no sequence? do you just trust that the latency from leaf to spine ...
    Jjekes
    last modified by Jjekes
  • Maintain Security and isolation for Server farm and guest network with Flat l2 network devices

    Hi, I am looking for your guide on a network design topic. Many times I have faced an issue with Network design especially on Server Farm and Guest Users. Many times our sales peoples will remove the L3 routing paper...
    Deepak
    last modified by Deepak
  • CDP and LLDP leaks

    Hi all,   I know that it is possible to disable CDP or LLDP at the interface level or globally. It is often done in the DMZ and sensitive networks for instance.   But if for any reason we cannot do that (t...
    Olivier
    last modified by Olivier
  • CCNA R&S Book's

    Hello CISCO member   i have little confusion about CCNA books. the original cisco press books have different ISBN numbers compare to Pearson INDIA books. which books i have to study. are Pearson INDIA and CI...
    Shakir
    last modified by Shakir
  • Network troubleshooting

    Hello everyone   does anyone knows where can i find a good material with deep troubleshooting steps ? like using a network monitoring tools and explanation of what is going wrong with the network ... does anyon...
    Matheus
    last modified by Matheus
  • New Study Group for CCIE RS-Slack

    Started a new Slack group- cciersteam.slack.com This is study group focusing on CCIE RS track with INE as primary resource for Prep,   Let me know if anyone is interested, i can send invite, currently i have 3 ...
    Gary
    last modified by Gary
  • Netflow on Border Router and Aggregation Switch

    Hello experts. If I have netflow v9 configured for ingress and egress on my Border Router, and I have an Aggregation Switch behind it which is routing a VLAN that is not on the Border Router, then do I need to config...
    chad
    last modified by chad
  • Change Username

    Is there a way to modify my Cisco Learning Network username?
    chad
    last modified by chad
  • router ospfv3 or ipv6 router ospf?

    I recall sitting in a Cisco Live presentation on OSPF for v6 and I remember the presenter talking about using address families versus separate processes for v4 and v6 and he suggested that it was valid to run separate...
    Gary
    last modified by Gary
  • Increase Ports

    I would like to know how to increase the number of ports that I can connect to on the nexus 9000 switches .  When I view all the interfaces in the switch I see 64 interfaces but am only able to physically use 9 p...
    Eric
    last modified by Eric
  • Cisco ASA vs Cisco FTD

    Looks like we have to move from our Cisco ASA5500x series to the new FTD platform, and before I start down that road, I am needing to understand this platform.   So from what I can tell its bascially Sourcefire ...
    Steven Williams
    last modified by Steven Williams
  • OSPF virtual link Part 2

      https://wp.scsiraidguru.com/?page_id=2051   I added Area 2 below Area 1 and used virtual links back to OSPF Area 0.  On the right I will do all four types of stubs in part 3.
    Michael
    created by Michael
  • Two separate area 0 with virtual link

    Here is a Cisco VIRL simulation with two separate Area 0 using virtual links to connect the OSPF areas     https://wp.scsiraidguru.com/?page_id=1987
    Michael
    created by Michael
  • Bridging Help

    Hi   I am trying to connect to the asdm via my host machine into the virl network.  I have a 2nd USB nic cardi have given the address 172.16.1.254/24 and am bridging it with vmnet2 interface configured wit...
    simon
    last modified by simon
  • Using VIRL in more than one network

    Hi I've installed VIRL on a laptop at home, and when I get to work I can no longer use it. Do anyone have an idea to how I can use VIRL wherever I am regardless of IP adresses and all?   Jorn
    Ramnes
    last modified by Ramnes
  • Does a single CCNP exam recert all lower level CCNA certs?

    I have several CCNA certs that are expiring soon. I know if I go take a CCNA and pass that it will new the other CCNAs. The question that I have is if I take a single track of CCNP, for example 300-115 SWITCH, but not...
    Doug
    last modified by Doug
  • Certification

    Hi I am looking for Cisco video collaboration certification. Can anyone help in this for preparation and suggest on the type of question in exam. Is there anyone who has done this certification so far ?
    Vikas Kumar
    last modified by Vikas Kumar